Sale!

Stainless Exhaust Header 4-2-1, Fiat 124 Spider 1971-78 – (SKU 27-6318)

, , ,
2 reviews|1 answered question

Original price was: $399.00.Current price is: $335.00.

Sold over the last few years: 88

STAINLESS STEEL
Performance Exhaust Header

  • 304 Stainless Steel
  • TIG Welded w/ stainless weld
  • Polished to a near mirror finish
  • Gasket to head included
  • 10mm thick machined flange
  • 1.5mm thick tubing
  • 35mm ID Primary
  • 57.15mm (2.25″) Collector

Connects to stock center muffler or our Performance Stainless 2.25″ Center Exhaust (SKU 27-9370). Dyno-tested performance.

Fits:

Fiat Spider 124 1971-78 (not CA or MD models from 1978)

Has enough adjustment to accommodate 2000 (1995cc) engine swaps into earlier cars.

 

The below images show the current design that you will receive (on the right).  Note the more gentle bend.  This allows for much better flow.

*Note: VAS Headers do NOT cause “excessive heat” in the engine bay, unlike some competitors. You will NOT burn up any surrounding components due to our headers.*

*You may need to trim the bottom of the 2 pipes on the header to bring up the down pipe depending on your year.*

SKU has changed from 27-6318-SS to 27-6318 (they are the same)

2 reviews for Stainless Exhaust Header 4-2-1, Fiat 124 Spider 1971-78 – (SKU 27-6318)

4.5
Based on 2 reviews
5 star
50
50%
4 star
50
50%
3 star
0%
2 star
0%
1 star
0%
Showing 1 of 2 reviews (4 star). See all 2 reviews

Customer Images

Image #1 from jeffrey c.
Image #2 from jeffrey c.
Image #1 from jeffrey c.

jeffrey c.

Your description could use a little more detail and some required parts were excluded from the requirements. It should be noted if you are buying the SS header and intermediate pipe, the front section of the intermediate pipe needs to be cut and a flex connector added to assemble the parts. Bolts for the down tube clamps should be included. Finally if the stud on the head asm have a shaft greater than 10mm, they should be replaced or you'll be required to use several washers. I am going to order the 30mm studs for the downpipe application. More detail and photos for your studs would also be helpful. I am very excited to get this installed.

(0) (0)
Image #2 from jeffrey c.

jeffrey c.

Your description could use a little more detail and some required parts were excluded from the requirements. It should be noted if you are buying the SS header and intermediate pipe, the front section of the intermediate pipe needs to be cut and a flex connector added to assemble the parts. Bolts for the down tube clamps should be included. Finally if the stud on the head asm have a shaft greater than 10mm, they should be replaced or you'll be required to use several washers. I am going to order the 30mm studs for the downpipe application. More detail and photos for your studs would also be helpful. I am very excited to get this installed.

(0) (0)
Image #1 from jeffrey c.
Image #2 from jeffrey c.
1-2 of 2 reviews
  1. Avatar photo

    Your description could use a little more detail and some required parts were excluded from the requirements. It should be noted if you are buying the SS header and intermediate pipe, the front section of the intermediate pipe needs to be cut and a flex connector added to assemble the parts. Bolts for the down tube clamps should be included. Finally if the stud on the head asm have a shaft greater than 10mm, they should be replaced or you’ll be required to use several washers. I am going to order the 30mm studs for the downpipe application. More detail and photos for your studs would also be helpful. I am very excited to get this installed.

    Image #1 from jeffrey c.
    Image #2 from jeffrey c.
    (0) (0)
  2. Avatar photo

    Finally got around to installing these headers . The material looks good in quality and appearance. The installation was fairly easy as well by using a six inch flex pipe from Totalflow ( the middle exhaust pipe had to be cut back some). The only small issue i had was a slightly off alignment on the welded on clamps of the two to one section, could not use an open end and ratchet, had to use to open end wrenches. Otherwise perfect.

    (1) (0)
Add a review
You must be logged in to post a review Log In

Q & A

Does this fit 1982 124 Redout asked on April 4, 2023

Hello,

No as the description states this is for 1971-78 years. The 1982 year uses SKU 27-6320.

Thanks
Vick Autosports

Matt Phillips answered on April 4, 2023 store manager
(0) (0)

Ask a question

Your question will be answered by a store representative or other customers.

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

Thank you for the question!

Your question has been received and will be answered soon. Please do not submit the same question again.

Error

Warning

An error occurred when saving your question. Please report it to the website administrator. Additional information:

Add an answer

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

Thank you for the answer!

Your answer has been received and will be published soon. Please do not submit the same answer again.

Error

Warning

An error occurred when saving your answer. Please report it to the website administrator. Additional information:

Make Model Year
Make Model Year
FIAT 124 Sport Spider 1971
FIAT 124 Sport Spider 1972
FIAT 124 Sport Spider 1973
FIAT 124 Sport Spider 1974
FIAT 124 Sport Spider 1975
FIAT 124 Sport Spider 1976
FIAT 124 Sport Spider 1977
FIAT 124 Sport Spider 1978
Shopping Cart